Plumbing Essentials: A Prerequisite for Installing a Bathtub
Plumbing Essentials: A Prerequisite for Installing a Bathtub
Blog Article
In this article below you will discover a good deal of extremely good additional info in regards to Installing A Bathtub.
Mounting a bath tub isn't precisely rocket science, yet it does call for strong plumbing, woodworking, and in some cases, tiling abilities. Changing an old bath tub with a new one is also a reasonably tough project. If the old bathtub is easily accessible, the job can move easily; if you have to open up a wall to eliminate the old tub as well as place the new tub, the task is much harder. In either case, the task is within a house handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the brand-new one. See to it you have qualified yourself for the job as well as fit trying it. Rather than employing a service provider to take control of a halfway-completed job, it is far better to consider employing one prior to you begin. Possibilities are you may require a specialist plumber to make tube links.
This post will assist you mount a new bathtub in your restroom if you have currently acquired a brand-new bathtub and don't need to change the arrangement of your previous water system pipes.
Your tools and also product list should comprise the following:
Getting ready for the Installation
To start with, the supporting structure supplied with the bathroom ought to be fitted (if needed) according to the supplier's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to make sure that if the faucet features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to avoid stress on the bathtub.
Fit the flexible tap connectors to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Utilize the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your setup, then the first thing you ought to do is detach the water system. After doing so, switch on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic due to the limited gain access to that is commonly the situation.
Use a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will come from the pipes. As soon as the supply pipelines have been eliminated, use the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from transforming during this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any old sealing compound.
Before proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Tub
Using both wooden boards under its feet, position the bathtub in the needed position. The wooden boards are practical in evenly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto 4 tiny points.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the level and also readjusting the feet on the bath tub until the level reviews level.
To install taps, fit the bottom of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; then do the same for the other tap.
Switch on the water supply and also examine all joints as well as new pipework for leaks and also tighten them if essential. Fill up the bathtub and also examine the overflow outlet and also the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the bath tub should wait up until the bath tub has been utilized at the very least once as this will certainly resolve it into its final placement.
Fitting New Touches
If the tails of the new taps are plastic, then you will require a plastic connector to avoid damages to the thread. One end of the port fits on the plastic tail of the faucet and the various other end gives a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, position the faucet in the placing opening in the bath/basin ensuring that the washers are in area between the faucet and also the sink. Secure the faucet in position with the producer supplied backnut. As soon as the tap is firmly in position, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical tap connectors. The previous kind ought to be linked to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to split a rigid seal, triggering the water to penetrate the wall in between the bath as well as the tiling, leading to problems with wetness and possible leakages to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures and fittings. They are offered in tubes and also cartridges, and also are capable of securing gaps as much as a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to enable the movement experienced when the tub is in use. The sealant can split relatively very early if you do not take into account this movement before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the marketplace. It is a good idea to fit the tiles using water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on A Step-by-Step Guide to Installing a Bathtub? Put feedback directly below. We will be interested to see your thinking about this review. We hope to see you back again later on. Do you know about somebody who is serious about the topic? Do not hesitate to promote it. I value reading our article about A Step-by-Step Guide to Installing a Bathtub.
We're here 24/7, call! Report this page